Darkglass Electronics - Microtubes 900 Bass Amplifier
The Darkglass Electronics Microtubes 900
A 900W amplifier equipped with an all analog pre-amplifier and a Class D Power Module. The first thing you will notice from the Microtubes 900 is its unusual control layout: On the right side you’ll find the clean section which is the foundation of your tone. It features Gain and Master controls an active 4 band EQ. Along with Low and Treble controls you will find Low Mids and Hi Mids control, each knob with their own 3-way frequency switch. On the left side you will find the Microtubes Engine which acts as an extra channel that can bring your clean tone to the next level by helping you cut through the mix while adding anything from subtle tube break up, harmonics and natural compression to obliterating distortion.
From Tyler Hesford, resident bass expert at Quest Musique:
"The Darkglass Microtubes 900 is a 900w Class D amp with more bells and whistles than you can shake a bass at. This is the amp that makes me question the need for any fuzz or distortion pedals on my board, which is saying a lot as that’s nearly all I run.
Dialing in a tone is very easy using the 4 band EQ which features Bass, Low-Mids, High-Mids, Treble, along with a gain and master volume. The Low-Mids and High-Mids also feature 3-way frequency switch for extra precision. The thing that really separates the Microtubes 900 from the rest of the pack is the amazing “microtubes engine” featured on the left side of the amp. This adds an extra channel to your amp that can take your clean tone from a subtle tube break up, all the way to a face-melting distortion. It features both the “Vintage Microtubes” voicing as well as the “B3k”, which both sell for $295 CAD respectively, giving this amp tons of value.
All of this is jam packed in a 6.39Lbs small form casing, perfect for the touring player. Pair this with a Darkglass intelligent footswitch and you’re ready for nearly all of your bass playing needs!"
Front Pannel Features
Connect your instrument via a standard ¼” mono cable.
Switch from passive to active mode. Some active basses can have a hotter signal output which can make the amp distort early (feel free to use it on Passive move even with active basses if such additional distortion is desired).
Turns on or off the Microtubes Engine to add natural compression, organic harmonic enhancement, and saturation ranging from mild overdrive to high gain bass rage.
The Microtubes Engine operates before the clean section (you can therefore use the 4 Band Active EQ for additional tone shaping in addition to the Tone knob described below).
Controls the amount of distortion that the Microtubes Engine will deliver. It will change from a soft warm overdrive to a massive modern distorted tone.
Controls the high harmonic content of the Microtubes Engine via a variable low pass filter: crank it up for additional attack and definition or dim it down for a smoother sound. This is handy if running bright clean EQ settings or cabinets with tweeters.
Controls the Microtubes Engine’s output volume.
Mixes between the Clean signal and the Distortion signal (Microtubes Engine).
Selects between two overdrive voicings: B3K mode will deliver an aggressive, percussive sound while the VMT will bring up the mids for a warmer, more neutral character.
Changes the volume of the signal the Active 4 Band EQ. You can set it low prior to ensuring the cleanest operation possible or set it higher for more aggressive growl.
+-12dB at 80Hz. Changes the low content of the signal.
+-12dB of the selected frequency via the LOW MIDS switch (described below). Changes the lower mid content of the signal.
Use this switch to change the frequency of the low mid band from 250Hz, 500Hz or 1kHZ.
+-12dB of the selected frequency via the HI MIDS switch (described below). Changes the higher mid content of the signal.
Use this switch to change the frequency of the hi mid band from 750Hz, 1.5kHz and 3kHZ.
+-12dB at 5kHz. Changes the high content of the signal.
Controls the overall volume of the amplifier.
Mutes the amplifier.
Back Pannel Features
Connects the amplifier to your cabinet. This Speakon combo jack allows for either Speakon or ¼” speaker cable operation.
*WARNING: Do not use an instrument cable with this jack. Using an instrument cable can damage your amplifier.
Press when using a 2Ω load. You can use this control to lower the output if your 4Ω cabinet is not able to handle more than 500W (you can also get 350W with an 8Ω cabinet in this configuration).
Pre Amp Out
This output connects the preamp to a different power amp.
Power Amp In
Use this input to connect a different preamp to the power amp. (master volume will be disabled)
Selects what signal will be delivered by the DI output. Selecting PRE, sends a clean copy of your input bass signal. Selecting POST delivers a signal processed by the preamp of the amp (gain, distortion, eq, master, etc.)
Lifts the ground of the DI XLR output. If a ground noise in you DI signal is experienced, try changing the setting of this control.
Connects the Microtubes 900 preamplifier to balanced equipment (mic preamp, console, recorder, compressor, audio interface, etc.) via a standard XLR jack.
The Footswitch allows you to remotely engage and disengage the Microtubes Engine. Hold the footswitch to Mute the amplifier. The VMT/B3K push button will remain operational with the Intelligent Footswitch plugged in.
* Use a regular mono instrument cable to connect the amplifier to the footswitch.
* Remove the cable from the footswitch jack in the rear panel if you want to control the amp from the front panel.
* The Microtubes 900™ will only work with our proprietary Intelligent Footswitch (included with the amplifier). A generic Footswitch will not work with the Microtubes 900.
Product description contributions by Tyler Hesford. Looking for more information on the Microtubes 900? Contact us!
Questions? Call our staff! We'd be happy to help. 1-866-386-5638